Rotary Evaporator w CSA approval, Across International Ai SolventVap 2.6-Gallon/10L w/ Motorized Lift, New
Rotary Evaporator, Across International Ai SolventVap 2.6-Gallon/10L w/ Motorized Lift, New
10L Rotovap with CSA approval
Vacuum pump Ulvac 1.6cfm with CSA approval
Chiller AI C30 with CSA approval
The new Ai SolventVap 10L series rotary evaporators is now ETL tested to UL/CSA standards (optional). This certification is required by many municipalities, and it also provides a higher standard of equipment safety and lifespan. SolventVap comes with all PTFE valves for solvent-resistant operations. We also lowered the height of assembled unit, for easy installation and ease of use and storage. Also come with them are vertical glassware and digital temperature/rotation control. Its optimized bath volume allows for rapid heat-up times. The condenser unit has specially designed glass tubes that utilize surface area extremely efficiently. That’s why our SolventVap evaporators consistently deliver reliable and reproducible process results that are usually reserved for more costly systems. Another important aspect of the SolventVap is the safety features, which includes dry-run protection, water bath over-temperature shut-off protection, and fuse protection.
Rotary evaporator features a specially designed motor and worm gear, which provides constant rotation at speeds from 10 to 130 rpm. As the flask containing the solvent is rotated, it continually transfers a thin layer of liquid over the entire inner surface. This gives a very large surface area for evaporation, which is caused by the gentle heating from the water bath. The rotating system is fitted with a special seal that allows the apparatus to be placed under vacuum, effectively reducing the boiling point of the solvents and removing the vapor phase, making the process much more efficient. Each unit is also equipped with an easy-to-use vacuum release and a continuous feed system, which allows solvent to be constantly drawn into the rotating flask without needing to stop the operation.
Digital water bath operates from ambient temperature to 99°C (210°F) with PID temperature control stepping at 0.1°C increments. Heating coils are located directly inside the pan for the most efficient heating possible. A built-in overheat protector will shut down power, should the controller fail.
Standard Glassware Set includes 2.6 gallon (10 liters) round-bottomed evaporating flask, 1.3 gallon (5 liters) round-bottomed receiving flask, and vertical condenser. Rotary evaporators with vertical glass condenser are great for distillation of solvents with higher boiling points.
•UL 61010-1, CSA C22.2 and CE certified (optional)
•Water bath cover enhances safety by protecting evaporating flask and the material inside; it gives you uniform temperature inside evaporation flask as well as energy saving by reducing heat loss. It also creates a better lab environment by preventing heat and humidity from escaping.
•New stronger swivel casters can be securely adjusted to accommodate uneven floor.
•Solvent-resistant PTFE and Viton gaskets, ensuring long time operation.
•Specialized motor with extremely compact, intermeshed worm and worm gear provides precise driving for very quiet, vibration-free operation.
•Downward-condensing vacuum connection design ensures safe vacuum operation.
•Motorized water bath lifting for precise control.
•Easy, straight-forward visual operation with digital speed and temperature display.
•PID temperature controller ensures accurate temperature control is maintained.
•One year warranty on rotary evaporator except for glassware and all sealing gaskets.
Your safety is important to us! Please use caution when operating. Users of glass reaction equipment must take all necessary precautions to avoid contact with rotating parts, particularly entanglement of loose clothing, hair, necklaces, or other jewelry. Under these circumstances, the winding action of the rotating parts can draw the user(s) into the apparatus, resulting in breakage of glassware, burns, and/or chemical exposure. Extra caution must also be taken when operating with air-reactive materials, especially under vacuum. A leak can draw air into the apparatus and cause a violent reaction to occur.
220V 50/60Hz single phase, 17.3A, 3800 watt (rotation motor: 300 watts)
Glass material High borosilicate glass 3.3
Capacity: 2.6 gallon (10 liters or 0.35 cu ft)
Maximum load: Not to exceed 60% of the flask’s capacity
Sealing flange: 4.9″ diameter
Rotation speed: 10 to 130 rpm
Evaporating speed: 0.75 gallon/hour (water), 1.5 gallon/hour (alcohol)
1.3 gallon (5 liters or 0.18 cu ft)
Condenser Glassware: Main + auxiliary triple-circulating cold traps, vertical
Chilling fluid conneciton: 3/8″ hose barb x 4 (2 on main + 2 on auxiliary)
Main condenser: 3,900 cm2 or 4.2 sq ft
Auxiliary condenser: 2,530 cm2 or 2.7 sq ft
5 to 95°F
Temperature range: ambient to 99°C (210°F)
Temperature controller: digital
Dimensions: 12.5″ diameter x 8.7″ depth x 11″ height
Material: stainless steel
Media: distilled water only
Max. water level: not to exceed 1″ from the top rim of the bath
Number of heaters: two
Drain port: one
Exterior liner: rubber
Maximum lifting distance: 4 inches
Vacuum level: < 3 torrs Vacuum sealing: PTFE + Viton gaskets Vacuum connection: 3/8" hose barb x 1 on main condenser Swivel casters Four, built-in with locks Safety Dry-run, over-temp shut-off, built-in circuit breakers Shipping weight 200 Lb (evaporator), 100 Lb (glassware) Unit dimensions 36 x 22 x 67" (WxDxH) Shipping dimensions 39 x 22 x 44" (evaporator), 30 x 25 x 28" (glassware) (WxDxH) Download Product brochure Compliance UL 61010-1: 2012 Ed.3 + R: 29 Apr 2016 CSA C22.2# 61010-1-12: 2012 Ed.3+ U1; U2 (R2017) CE Ai C30 series recirculating chillers are the true thermostatic control laboratory chiller, these closed laboratory chillers are ideal for applications such as cooling rotary evaporators, analytical instrumentation, laser etching, ICP, vacuum systems, plasma etching and jacketed reactors. This system can also be used as a replacement to tap water cooling in laboratory applications. Ai C30 are compressor-based recirculating chillers that offer outstanding performance and high reliability as well as quiet operation and ease-of-use. Powerful force/suction pump provides constant flow rates, while microprocessor PID controller gives you the ideal solution when you need precise temperature control or cooling below ambient temperature. IMPORTANT! -30°C/-22°F ULTIMATE TEMPERATURES ARE TESTED UNDER EMPTY LOAD CONDITION (NO ROTARY EVAPORATORS OR JACKETED REACTORS ATTACHED). C30 circulating chiller features •UL 61010-1 and CSA C22.2 certified (optional) •No dry ice or liquid nitrogen needed •Advanced PID digital temp controller •Built-in chilling fluid filter protects the recirculating pump and prevent blockage •All steel construction for durability •Eco-friendly R410A refrigerant •Cost saving as the water consumption is completely eliminated •Built-in casters for mobility •Insulated tubing included •Recommended for 10L rotary evaporators Manufactured and imported directly from Japan, ULVAC DTC series diaphragm pumps feature integral forced-air cooling. They have two-stage PTFE diaphragms that are ideal for pumping corrosive gases and organic solvents. These pumps are oil-free, portable, and chemical-resistant, which means less maintenance and no more frequent and costly oil change, or cross contamination. Ai is now the official dealer of ULVAC vacuum pumps. These pumps are made in Japan with one year warranty and technical support from ULVAC. Features: ◦UL/CSA listed ◦Only PTFE components are exposed to vacuum, ideal for pumping corrosive gases and organic solvents ◦Integral forced-air cooling ◦Very compact and portable ◦Designed to back most hybrid turbo pumps Applications: ◦Rotary evaporator ◦Evaporating system ◦Vacuum concentrator ◦Vacuum filtration ◦Vacuum drying systems ◦Medical/pharmaceutical equipments ◦Centrifuge ◦Laser-gas circulation